Switching to the low power TinyDuino platform.

After sending the first gen housings out for some real world testing, I returned my attention to the guts of my data loggers.  While the Uno & Adafruit data logging shield was dead easy to get up and running, the whole unit would wring out 6AA’s in about a day, and I needed a heck of allot more run-time than that.

So I started combing through the forums at the Arduino playground for any power management threads I could find. A myopia inducing week of screen reading later, I had developed a rough list of strategies to pursue, even though I had no idea how much difference each one would make. These fell into two basic categories:

Lower the voltage & clock frequency,  then get rid of any circuits you don’t need:
– like indicator leds, voltage regulators, usb interfaces, etc

and once you have that sorted:

Turn off parts of the processor you are not using with software:
– and if possible put the whole chip to “sleep”

And although I did not find this mentioned anywhere, I also penciled in a note to research different battery chemistries, as I knew that on year long time scales, self discharge was going to be a real issue.

So I started with the hardware, and dug into the stunning array of “bare bones” clones that had spun off since Banzi et.al gave their little project to the world. I whittled the list down to a handful of low power units including: the Pro Mini,  the Solarbotics Ardweeny, the Rocket Scream Mini Ultra, Modern Device Jeenodes, RFduinos, and a few others that seemed to be pushing the limits of low power design. Some of these designs were so minimal, they were barely more than a row of breadboard pins soldered onto the raw Atmel chip itself. So, for a while, I flirted with the idea of just sticking a chip on a mini breadboard and going from there.

I was comfortable with the idea of using a separate FTDI breakout board to program the unit, but some of the low power designs had non standard processor chips, and I knew that was not going to work, because I was still cutting my teeth on “Coding for Dummies” tutorials. And on a purely practical level, the mini breadboard I used with an Ardweeny started getting ugly once I wired in the SD card shield, the accelerometer, the FTDI chip, the battery connectors, etc.  I was not sure the resulting octopus would survive the bashing around these sensors were likely to see dangling from the side of a cave diver, no matter how tough my housings were.

Then, I got wind of a spectacularly successful Kickstarter campaign  for a new, ultra small Arduino board that was being made in Ohio, and everything just fell into place.  While the new TinyDuino system was a bit expensive, it delivered almost everything on my power management wish list and they also had an accelerometer, an SD card shield, with several protoboards.  But rather than describe the effect of all this with words, perhaps a picture would convey all this a little better:

Alpha VS Beta

My digital innards went from an alpha kludge to a running beta in one fell swoop!

So although I had some misgivings about their fragile looking stack connectors, adopting the Tinyduino meant that I could now start chewing on the gnarlier bits of software based power management.

The hardware selection had essentially just been one long process of elimination, but I knew right from the start that coding would put me on a much steeper learning curve. AVR assembly language still seemed like quasi magical incantation, so I just started gathering every example of “sleep code” I could find, like a squirrel collecting nuts for winter.  I figured I would just try to  cut & paste from simple examples like the Nightingale code until I was successfully shutting down the cpu, and waking it with the internal watchdog timer on eight second cycles, to check if it was time to read data.

But I kept finding comments in the forums about how sloppy the Atmel internal clocks could get, affected by everything from temperature variations and input voltage, to “animal spirits”.  With so many iterations needed to extend those “overflow interrupt” blips out to a real world sampling cycle of perhaps 15 minutes, or even an hour, I worried that even tiny timing errors would eventually accumulate into sizable ones. (And recently I have heard rumors of people locking up their Arduinos because of watchdog timer conflicts with the default bootloader)

So I started investigating the use of an external real time clock (RTC) to let the little logger sleep for extended, and hopefully more precise, times between wake cycles.  There were tantalizing clues out there that this could make a system run for years, but I could not  follow the discussions far enough into the technical brambles to really understand them. And if I had thought that the machine code for sleeping was hairy, trying to pick a suitable RTC by looking at libraries and data sheets, seemed like it might convert an already steep learning curve into a straight vertical line.

Fortunately, it was then that I found an excellent post on power saving techniques which had clear examples of how to both sleep, and wake up the cpu with alarm interrupts. I was back in the game, and for the first time I had a sense of what all these things were actually contributing to my overall power budget. Combining his I2C primer  with the DSS circuits post on the Effects of varying I2C pull-Up resistors, and a few more tweaks, I finally managed to get a chronodot RTC (on the left in the picture above) to wake my sleeping data logger at any time interval I wanted.

Whew! My little project was finally looking like it might go the distance, and I was thanking the Gods for mysterious Über-tecks on the other side of the world, like Nick Gammon, who had put their mild obsessive compulsive disorders to such great effect bailing out newbies like myself.

<—Click here to continue reading—>

This entry was posted in The quest for low power. Bookmark the permalink.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s